SIGNUP - FREE Membership and 1 FREE Sewing Lesson
| FAQ | Login
 

Forum > Sergers, Coverstitch and Blindhemmers > What is wrong with my serger? ( Moderated by CarolynGM, Deepika)

Please LOGIN or Join PatternReview
Go to Page:
What is wrong with my serger?
Please help me troubleshoot
Deepika
starstarstarstar
Deepika  Friend of PR
Intermediate
MA
Member since 11/28/01
Posts: 11623
Founder
online now
Send Message

      
thumbsup 1 member likes this.



Date: 3/3/12 9:57 PM



This is the underside. See the loops? Something is messed up. I've changed the needles, fabrics, adjusted looper and needle tensions but nothing seems to work. Any ideas?

------
- Deepika
Founder, PatternReview.com
Blog: http://www.deepikablogs.com

simplystitches
simplystitches
NY USA
Member since 2/12/06
Posts: 1333
Send Message

      



Date: 3/3/12 10:14 PM

Your needle thread is loose and/or the lower looper is too tight. This is the process I use to balance the threads.

First make sure your needle thread is properly seated in the tension disk. Start off tightening the needle thread 1/2 a number. I like to grab a biggish scrap and serge at least 6-8" to give the tension time to take hold. Keep changing it 1/2 a number til it close to right. At that point you may have to play with lowering the lower looper the same way, by 1/2 a number.
You may get to a point 1/4 a number works.

These suggestions were made on the assumption that that's the back side. If it's the top side adjust the upper looper if needed.

Debbie

Pamela R
star
Pamela R  Friend of PR
Expert/Couture
ON CANADA
Member since 6/22/07
Posts: 610
Send Message

      



In reply to Deepika


Date: 3/3/12 10:35 PM

It looks like your needle thread is not in the tension disks, or there is something inbetween the tension disks so that they cannot hold the thread.
Try loosening the tension off all the way and then clean between them.
I often thread a piece of dental floss with a knot in it, around between the disks and pull it back and forth to try and get whatever it is out.
Usually the problem in a wadd of thread or a knot.

Hope this helps.

PattiAnnJ
star
PattiAnnJ
Advanced
OH USA
Member since 12/3/06
Posts: 7261
Send Message

      



Date: 3/3/12 11:00 PM

When the serger acts up it is time to re-thread.

Make sure the thread antenna is at it's highest position.

Set the tensions to zero and raise the presser foot.

Begin the threading according to the manual - always in the sequence instructed.

Set the tensions back to mid range, lower the presser foot and stitch a chain. If it is as it should be, then your threading has been successful.

Always test the stitching and settings with scraps of the project fabric before you begin construction of the project.





-- Edited on 3/3/12 11:03 PM --

------
I dont give them Hell, I just tell the truth about them and they think its Hell. Harry Truman

"Improvise, adapt and overcome." - Clint Eastwood/Heartbreak Ridge

a7yrstitch
star
a7yrstitch  Friend of PR
Intermediate
TX USA
Member since 4/1/08
Posts: 5836
Send Message

      



In reply to Deepika


Date: 3/3/12 11:09 PM

Adding future search term.

sergerstitchingthread

------
I have no idea what Apple thought I was saying so be a Peach and credit anything bizarre to auto correct.

Sew4Fun
starstarstarstar
Sew4Fun
Advanced
AUSTRALIA
Member since 6/23/04
Posts: 4874
Send Message

      



In reply to Deepika


Date: 3/4/12 1:30 AM

Definitely a problem with the tension on the needle thread. It's so loose I'd guess the thread isn't seated properly in the tension disc, so there is no tension at all. Unthread the needle thread completely, make sure your presser foot is lifted and start again rehtreading the needle, taking special care when passing the thread through the tension disc. Also check there is no loose thread caught in the tension disc. HTH

------
Belinda. Melbourne, Australia
http://sew-4-fun.blogspot.com/

Deepika
starstarstarstar
Deepika  Friend of PR
Intermediate
MA
Member since 11/28/01
Posts: 11623
Founder
online now
Send Message

      



Date: 3/4/12 8:34 AM

Thanks I'll try this today and report back.

------
- Deepika
Founder, PatternReview.com
Blog: http://www.deepikablogs.com

stirwatersblue
star
stirwatersblue
Intermediate
KS USA
Member since 12/13/08
Posts: 3217
Send Message

      
thumbsup 1 member likes this.



Date: 3/4/12 12:35 PM

I haven't been serging long, but I think I've had every single one of the mentioned things happen! LOL

My most common is probably forgetting to raise the antenna, although this week I had a Really Weird & Silly Thing go wrong--my right needle tension was way too tight, tho' it was at the right setting, and I couldn't figure out why... until the thread broke. Turns out the thread (I was using an older spool of normal sewing thread) had gotten caught in the little slit on the edge of the spool that keeps the thread from unraveling! Flipping the spool over so that slit was at the bottom solved that little glitch.

Obviously that is not your problem, but my point is that starting from scratch can clear up a whole host of problems whose sources aren't easily identifiable. (On my machine, I've also run into trouble when I haven't gotten the needles seated *just exactly right,* so that is something I would need to check out if rethreading didn't help.)

Good luck!

Good luck!

------
~Gem in the prairie

threaddy
star
threaddy  Friend of PR
Advanced
WY USA
Member since 4/22/09
Posts: 2945
Send Message

      



Date: 3/4/12 12:45 PM

Whenever I have a serger stitch problem I go to the different colored threads and then I can really see which thread is doing what. red, green, yellow and blue are the colors I use. It does look like something is goofy with your needle tension.
-- Edited on 3/4/12 12:48 PM --

------
"The problem is not that there are problems. The problem is expecting otherwise and thinking that having problems is a problem." Theodore Rubin
"Life isn't about finding yourself. Life's about creating yourself." George Bernard Shaw
Dan 9:24-27

Bernina vintage and computerized, Bernina and BL sergers , BLcoverstitch (a stray Pfaff and Viking followed me home too)

Deepika
starstarstarstar
Deepika  Friend of PR
Intermediate
MA
Member since 11/28/01
Posts: 11623
Founder
online now
Send Message

      
thumbsup 1 member likes this.



Date: 3/4/12 12:52 PM

It worked! Now I can sew.

------
- Deepika
Founder, PatternReview.com
Blog: http://www.deepikablogs.com

Go to Page:
Please LOGIN or Join PatternReview

printable version Printable Version

* Advertising and soliciting is strictly prohibited on PatternReview.com. If you find a post which is not in agreement with our Terms and Conditions, please click on the Report Post button to report it. Sergers, Coverstitch and Blindhemmers >> What is wrong with my serger?

 
adv. search»
pattern | machine | member
        
Clone Your Favorite Garment
Clone Your Favorite Garment

Register

Beginners Guide to Sewing Jackets
Beginners Guide to Sewing Jackets

Register

McCall's 6560

photo
by: nickelc624

Review
Favorite Things Little Bow Peep Pattern

Favorite Things Little Bow Peep Pattern

Buy Now
Fusible Interfacing DVD

Fusible Interfacing DVD

Buy Now

Conditions of Use | Posting Guidelines | Privacy Policy | Shipping Rates | Returns & Refunds | Contact Us | About | New To PR | Advertising

Copyright © 2014 PatternReview.com® , OSATech, Inc. All rights reserved.