SIGNUP - FREE Membership and 1 FREE Sewing Lesson
| FAQ | Login
 

Platinum Sponsor
PatternReview.com
PatternReview.com

Forum > Pattern Modifications, Design Changes & Pattern Drafting > Sleeve placket with two-piece sleeve?

Please LOGIN or Join PatternReview
Go to Page:
Sleeve placket with two-piece sleeve?
sydney800
star
sydney800
Intermediate
Member since 2/13/10
Posts: 2
Send Message

      
thumbsup 1 member likes this.



Date: 12/2/12 3:04 PM

Hello! First-time poster here! I was hoping someone could weigh in on inserting a sleeve placket on a shirt with a two-piece sleeve. If this topic has been addressed elsewhere, please let me know! I am making M6436, and one sleeve seam lines up with the side seam, while the other falls further back where the placket would normally be attached. The instructions would have you turn the edges under and stitch, leaving a slit rather than have any overlap. I am considering adding either a continuous lap binding or a sleeve placket. My questions are:
1) would a placket look odd set on a seam? Would a continuous lap be the better choice?
2) How do I best address the seam finish? I am planning to do a flat-felled seam, and was thinking of finishing it to the top of where the placket would be, and then trimming the seam allowance below and inserting the placket or lap afterward. Hopefully, I would be able to then line it up so the "step" of the flat-felled seam would be enclosed in the top of the placket. Does this make sense? Any suggestions? Thank you!

SunnyAlta
SunnyAlta
Intermediate
Member since 7/11/10
Posts: 314
Send Message

      



Date: 12/2/12 5:16 PM

DH has a RTW shirt with 2 seams on the sleeve. The placket goes over a top-stitched seam. Seam does not line up with the very middle end of the placket but falls more towards the side of the placket. (It's not centered to where they meet.) Believe it's a one piece placket cut to be folded & then stitched but cannot say for certain. The other seam is flat-felled & a little more "stiff". Not sure I'd do a flat-felled seam where it meets with the placket as it will leave some bulk. DH's shirt is just a thin cotton.

You might check Pam's site to see if she has anything helpful there.

http://off-the-cuff-style.blogspot.ca/

sydney800
star
sydney800
Intermediate
Member since 2/13/10
Posts: 2
Send Message

      



In reply to SunnyAlta <<


Date: 12/2/12 11:17 PM

Thanks for the reply and the link. Is the seam with the placket serged and top-stitched, since it's not flat-felled? I will have to do a couple of practice pieces, as well as check out the link you posted!

Pam~Off The Cuff~
star
Pam~Off The Cuff~  Friend of PR
Expert/Couture
New York USA
Member since 4/18/05
Posts: 122
Send Message

      



In reply to sydney800 <<
thumbsup 1 member likes this.


Date: 12/3/12 8:08 AM

Hi!
Although I have many shirt-making tutorials on my site,
http://off-the-cuff-style.blogspot.com
I do not have a tutorial about placket construction on a 2-piece sleeve. Why? I don't particularly like 2-piece shirt sleeves, so I do not draft patterns that have them. ;)

------
~Pam

Pamela Erny
OFF THE CUFF ~Style~
www.Off-The-Cuff-Style.blogspot.com
and My Store...
www.FashionSewingSupply.com !

SunnyAlta
SunnyAlta
Intermediate
Member since 7/11/10
Posts: 314
Send Message

      



In reply to sydney800 <<


Date: 12/3/12 8:58 AM

Yes, the seam is serged & then top-stitched.

Bombyxmori
Bombyxmori
Intermediate
Member since 12/1/12
Posts: 4
Send Message

      
thumbsup 1 member likes this.



Date: 12/24/12 11:34 PM

First time poster here as well, probably coming in weeks after completion of your blouse.

I made M6613, which calls for the same cuff treatment. Since I'm new to shirtmaking and trying to learn classic techniques, I taped the sleeve pattern pieces together, then used DPC's placket pattern and method. FWIW, having read Pam's blog extensively gave me the confidence to do this. And it came out fine.
-- Edited on 12/24/12 11:36 PM --

Go to Page:
Please LOGIN or Join PatternReview

printable version Printable Version

* Advertising and soliciting is strictly prohibited on PatternReview.com. If you find a post which is not in agreement with our Terms and Conditions, please click on the Report Post button to report it. Pattern Modifications, Design Changes & Pattern Drafting >> Sleeve placket with two-piece sleeve?

 
adv. search»
pattern | machine | member
        
Bust Adjustments
Bust Adjustments

Register

Expert Sewing Techniques for Jackets
Expert Sewing Techniques for Jackets

Register

Vogue Patterns 8821 OOP

photo
by: FreyaStark

Review
Sewing Workshop Village Bag Pattern

Sewing Workshop Village Bag Pattern

Buy Now
Favorite Things The Boot Slippers Pattern

Favorite Things The Boot Slippers Pattern

Buy Now
Self Drafted Pattern 235056-1002

photo
by: Quickie

Review

Conditions of Use | Posting Guidelines | Privacy Policy | Shipping Rates | Returns & Refunds | Contact Us | About | New To PR | Advertising

Copyright © 2014 PatternReview.com® , OSATech, Inc. All rights reserved.