Online Sewing Class: More Knits
SIGNUP - FREE Membership and 1 FREE Sewing Lesson
| FAQ | Login
 

Forum > Beginner's Forum > Thread tension question on light vinyl ( Moderated by EleanorSews)

Please LOGIN or Join PatternReview
Go to Page:
Thread tension question on light vinyl
Bottom thread wonky on lightweight vinyl
beserres
beserres
District of Columbia USA
Member since 4/17/13
Posts: 4
Skill: Intermediate
Send Message

      



Date: 5/26/13 9:37 PM

Hello - I am sewing through a very lightweight vinyl, testing out my machine's (baby lock quest) dual feed for using vinyl so I can try out a faux leather bag. I have the upper thread tension set at 7, my machine always seems to need high thread tensions or else the stitch is very loose. The top comes out perfectly straight, but the bottom comes out wonky, all most looking zig zag. It is pretty strong though. Any tips on tensions given the top being ok but the bottom being wonky? Should I play with the bobbin case's tension setting? Tighter or looser?

Thanks!
Ben

beauturbo
beauturbo
California USA
Member since 5/2/09
Posts: 4417
Skill: Advanced
Send Message

      



In reply to beserres <<
thumbsup 1 member likes this.


Date: 5/29/13 1:12 AM

Maybe it has nothing to do with the thread tension at all, and more to do with the vinyl trying to climb up the needle as sticking to it, or sticking to your stitch plate or even the little needle holes in the vinyl trying to close up and seal up before all the thread can travel though them. I think vinyl can be really kind of a stinker to sew on for lots of different reasons actually. If it was some thin clear vinyl sold off a roll, and had printed tissue paper cut off from it by the yard when you got it, you can use that same tissue paper on top or underneath it too, later even when sewing into it, and sometimes that stops some of that stuff.

Also if sewing it to fabric, having the fabric side down on the feed dogs most times sews better than having it the other way around I think.

Sewing clear thinnish non backed with anything else kind of vinyl on those rolls though just to it's self is something I don't like to do and try to avoid. If I can't avoid it, then I at least sew though some kind of paper, top or bottom or both, and rip that off afterwards. You could try that.

PattiAnnJ
star
PattiAnnJ
Ohio USA
Member since 12/3/06
Posts: 8155
Skill: Advanced
Send Message

      
thumbsup 1 member likes this.



Date: 5/29/13 10:05 AM

If the stitching is okay with a different fabric without changing the thread, tension or needle, then you may want to try using the layers of tissue.

I was going to suggest a Titanium coated needle, but only if the needle is the only issue.

When you thread the machine, do so with the presser foot up.

When you adjust the tension setting, be sure the presser foot is down.




-- Edited on 5/29/13 10:07 AM --

------
"Improvise, adapt and overcome." - Clint Eastwood/Heartbreak Ridge

"Isnít it a shame in todayís world you canít tell the truth. If you tell the truth youíre abrasive. If you lie youíre charming." - Bob Huggins/College Basketball Coach

Miss Fairchild
starstarstarstar
Miss Fairchild
USA
Member since 8/24/02
Posts: 7936
Skill: Advanced
Send Message

      



In reply to beserres <<


Date: 5/29/13 12:09 PM

Why not try a roller foot? It's made for leather, but it works on vinyl as well.

------
"Play the cards you are dealt, but choose who is sitting at the table"..AARP magazine

SEE MY ETSY SHOP HERE: http://www.etsy.com/shop/AuntMaymesAttic
My blog: http://auntmaymesattic.wordpress.com/

deeannb
deeannb
Michigan USA
Member since 4/28/13
Posts: 10
Skill: Advanced Beginner
Send Message

      
thumbsup 1 member likes this.



Date: 6/3/13 9:37 PM

Most of my sewing experience is on marine vinyl using an industrial walking foot machine. Will your machine have a walking foot attachment? Might change the way the vinyl is feeding through and thus improve the tension differences.

My first thought, with what you described, sounded like loose bobbin thread. If you have a spare bobbin case, try adjusting that one (I hate changing the bobbin tension on the bobbin case I usually use, because you can never seem to get it back to where you want it when you go back to 'usual' material).

Take care with making the thread too tight, and the stitches too short.

Go to Page:
Please LOGIN or Join PatternReview

printable version Printable Version

* Advertising and soliciting is strictly prohibited on PatternReview.com. If you find a post which is not in agreement with our Terms and Conditions, please click on the Report Post button to report it. Beginner's Forum >> Thread tension question on light vinyl

Merchants on PR

O! Jolly! Shop


Sweater knit fabrics
Deals!

Amulet Swim Fabrics


Poly/PBT swimwear fabric
Web site

Paganoonoo


Upcycle sewing patterns
Web site

Style Arc sewing dress patterns


Patterns That Fit
Web site

The Smuggler's Daughter


Online Fabric Store
Web site

 
adv. search»
pattern | machine | member
        
Online Class
Sewing Basics
Sewing Basics

Class Details

Online Class
Understanding Wool Fabrics
Understanding Wool Fabrics

Class Details

New Look 6804

photo
by: loke

Review
Favorite Things The Classic Shirt Pattern

Favorite Things The Classic Shirt Pattern

Pattern Details
9 inch Bent Handle Scissors

9 inch Bent Handle Scissors

Pattern Details
Simplicity 2938

photo
by: pt6356

Review

Conditions of Use | Posting Guidelines | Privacy Policy | Shipping Rates | Returns & Refunds | Contact Us | About | New To PR | Advertising

Copyright © 2015 PatternReview.com® , OSATech, Inc. All rights reserved.